Sunday, May 17, 2009

Engine work

Well I screwed up, just not sure how bad. I sprayed my engine with easy-off oven cleaner and apparently the chemical in easy-off likes to eat aluminum, which is what the engine is made of. Not good, although varying opinion on how bad. I made a mistake reading one of the restoration books and thought it said to use it for grease removal, and while it did in fact say that, it meant it for the cowls and undercarriage of the bike, NOT the engine. grrrr. So now my engine is all mottled white from what looks like left over easy-off remnants. Trying to figure out how to remove it. Here's what it looks like now.













Not much I can do about it now until I figure out a solution. CRC Lectra-Motive seems to be the recommended product, although there are plenty of other suggestions on scooterbbs, just search for engine cleaning and you'll get plenty of opinion.

Well regardless of the engine cleaning I went ahead and started taking apart the engine. Before you get started I highly recommend you read the vespa maintenance website. It goes in to much greater detail the do's and don'ts of taking apart your engine. You want to be particularly careful with your carb and piston, as you don't want random parts falling into your engine.

About the only thing I can add to what he says on the website is in regards to the circle clips on the piston. I wasn't able to get at them with needle nose pliers. There is a small hole on the ends of the circle clips. I was able to get a paperclip through the hole and then with needle nose pliers I was able to pull out the circle clip. I lost one of the clips because when it sprang out it went flying off the paperclip. I guess you could twist the paperclip around itself before trying to pull them out. I have new circlips all ready so I wasn't that worried about it.

That is all for now with the engine. Still deciding if I am going to crack her open. Probably will just to replace seals, and do a general looky loo. I mean I have the engine on the stand and pretty much taken apart at this point. I am probably also going to do a carb overhaul now that it is off.

My dog is puking so I need to go take care of him.

Thursday, May 14, 2009

Engine Stand DIY


Still waiting around so I figured, hey, why not start fucking around with my engine. Did some searching and came up with the following DIY engine stand. I made some modifications and I am going to post all of my instructions so it's easier for you than the bbs history shows, although it's pretty easy to figure it out.

Parts:
2x6's (I used random scrap wood from a construction site)
3 3/4" floor flanges
3 3/4" x 10" galvanized pipe
3 3/4" T's for pipe
1 1/2 x 24" threaded rod. Ask for where the random steel rods and metal are, it is usually close to the nuts and bolts but not always. You really only need 16" but they only sold it in 1' or 2' sections at my local hardware store. This is for the front mount
1 3/8 x 5" Bolt. For the rear mount
5 Fender washers
2 regular 3/8 washers
2 1/2 nuts
1" Deck Screws.

I went with 10" because I wanted to be able to have the kickstand go all the way down and it sounded like for some 8" wasn't enough.

You want the wood to be cut up as follows:
2 20x6x2
2 16x6x2

Go ahead and make a frame out of the four pieces with the 16" pieces on top. The floor flanges will be mounted on the 16" pieces. On one 16" piece, mark the center and then measure out 5 3/8 from the center of the piece. This is dead center of the flanges. Go ahead and screw the flanges down. This is easier without the pipes in.

Now go ahead and put two of the pipes in and their respective T's. Lining the t's up of course so the threaded rod can go through the engine mount. Find a friend for this next part. Grab your engine and line it up with the posts. Take the threaded rod and slide it through, starting from the rear tire side (NOT the kickstart lever side), make sure to put one of the fender washers and nuts on at the end you are not sliding through. As it goes through the first t but before it enters the engine mount put another fender washer. Push it through the engine. Before it enters the next t put another fender washer. As it comes out the other side put another fender washer and the last nut. Go ahead and tighten up the bolts a little. I took a hacksaw and this point and cut off the extra part of the rod I didn't need.

Now your engine is swinging on the front mount. From here put together the other pipe, t, and flange, prior to screwing it in. Swing up the engine. Line up the t with the rear mount. I put the t on the left side of the engine mount. This should be obvious because it won't fit on the right side. Push the 3/8 x 5 bolt through and put the nut on it. No need to tighten beyond hand tight at this point. Move the rear pipe and flange around until it looks straight and sits flat on your 2x6. Take a pen and draw a circle around the flange. Go ahead and pull out the bolt and let your engine swing back down. Take out the pipe and t and then put the flange back where you made your circle. Drill your screws and then redo. I did it this way because it was easier to screw the flange down with the pipe out of the way. You could of course do it after you have aligned everything with the engine and T.

I also mounted my flanges on top of a block on top of the 2x6. I did this because I wanted to use longer than 1" deck screws and figured 2 1/2" deck screws through 2 pieces of plywood would hold for sure. Probably overkill but when I first started this project I started out only with the 16" pieces and not the cross pieces. Kind of stupid. I would probably not do the blocks if I was to start this over.

This only cost me about $30 with the price of metal today.